想了解我们的软管泵,滑模机实地大厂产品吗?我们为您准备了细致入微的视频介绍,让您在短时间内了解产品的精髓。


以下是:软管泵,滑模机实地大厂的图文介绍


工业软管泵不锈钢齿轮泵,可输送非润滑油饮料低腐蚀性液体,配铜齿轮可输送汽油苯等低内点液体。由于齿轮泵自吸能力差,一般是由于齿轮泵泵腔间隙较大所致。同时也是如果齿轮泵输出端没有“止回阀”,则必须是下一级齿轮泵的止回阀或控制阀。移动固定后,周围工作人员可恢复手术。

Industrial hose pump stainless steel gear pump, can transport non-lubricant beverages with low corrosive liquids, with copper gears can transport gasoline, benzene and other low internal point liquids. Due to the poor self-priming ability of the gear pump, it is generally caused by the large gap between the pump cavity of the gear pump. At the same time, if there is no "check valve" at the output of the gear pump, it must be a check valve or control valve of the next gear pump. After moving and fixing, the surrounding staff can resume surgery.



众所周知软管泵在运行时,是通过一根U型附有弹性的橡胶软管来完成输送。今天小编需要强调的是,软管存放时间不宜过长,一般以一年为限。在停工期间,对装有软管的泵,若长期不用,每隔一个月需转动泵一次。以免压辊长时间压在泵管的某一处,减弱管子回弹性,影响其流量的输送。

It is well known that when the hose pump is running, it is conveyed through a U-shaped rubber hose with elasticity. Today the editor needs to emphasize that the storage time of the hose should not be too long, and it is generally limited to one year. During the shutdown period, if the pump is equipped with a hose, if it is not used for a long time, the pump needs to be rotated every other month. So as not to press the roller for a long time at a certain position of the pump tube, it will weaken the resilience of the tube and affect its flow rate.

 




随着不断的发展豫信致诚机械设备有限公司狠抓管理、完善经营机制,建立了一整套质量与售后保障体系,不断提高 新疆乌鲁木齐混凝土抛丸机产品科技含量以及服务水平,随时为迎接新的机遇与挑战做好准备! 同时我们随时欢迎来自社会各界的新老朋友一起为了我们共同的家园,相互交流,真诚合作,共同成长 !



软管泵的设计选型要求:
1、当工艺条件没有特定的要求时候,那么选泵的流量是可以大于实际的需求流量的。
2、工艺条件在连续生产的时候,那么它本身的实际需要流量要和额定的流量吻合,如果是有特殊的需求,那么可以选择变频调速的泵。
3、软管使用的温度要小于100℃,主要是在工作的过程中会产生热量,如果是周围散热条件比较好的时候,那么介质的温度可以达到一百。
4、主要成分是天然橡胶,因此在选用的时候,要考虑软管对介质的适应性。
5、进出口是在同一个方向的,并且进出口是可以相互之间调换的,可以根据具体的情况来定。          




点击查看豫信致诚机械设备有限公司的【产品相册库】以及我们的【产品视频库】